Apex Information Exchange Forum Index Apex Information Exchange
Hosted by Dr. John Kanca III DMD
 
 FAQFAQ   SearchSearch   UsergroupsUsergroups   REGISTER 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Visit Apex Dental Materials     Upload Photos To Your Post


Prefab metal Post with Anchor and Surpass

 
Post new topic   Reply to topic    Apex Information Exchange Forum Index -> About anchor®
View previous topic :: View next topic  
Author Message
rlp



Joined: 27 Jun 2008
Posts: 2

PostPosted: Fri Jun 27, 2008 2:03 pm    Post subject: Prefab metal Post with Anchor and Surpass Reply with quote

I watched the Apex video of a post and core with Anchor and Sim...but could somebody go thru the steps with using Surp intead of Sim?...

Does Surp 1-3 go down the canal space?...is it thin enought to light cure the Surp before placing the Anchor and post?...

Is an air syringe good enough to dry the post space or should I do the Strupp technique of hooking a centrix orange needle tip to the air syringe to make sure the canal is dried enough?..any other pointers?

Thanks!!!
Back to top
View user's profile Send private message
john kanca



Joined: 14 May 2005
Posts: 6346

PostPosted: Fri Jun 27, 2008 2:17 pm    Post subject: Re: Prefab metal Post with Anchor and Surpass Reply with quote

rlp wrote:
I watched the Apex video of a post and core with Anchor and Sim...but could somebody go thru the steps with using Surp intead of Sim?...

Does Surp 1-3 go down the canal space?...is it thin enought to light cure the Surp before placing the Anchor and post?...

Is an air syringe good enough to dry the post space or should I do the Strupp technique of hooking a centrix orange needle tip to the air syringe to make sure the canal is dried enough?..any other pointers?

Thanks!!!


Hi and welcome!

I do use all three parts of Surpass on post preps. I apply Surpass 1 into the canal and use a single paper point to blot up excess out of the post space only, and then apply 3 coats of Surpass 2, dry it thoroughly, apply another paper point to the canal space to pick up wet Surpass 2, then apply Surpass 3. Typically I use a micro-applicator (round tip microbrush) to apply a thin layer of Surpass 3 in the canal space, and then I light-activate it all.

Does that help?

Cool
_________________
"You need me on that wall."


"You don't have a town named after you"
Back to top
View user's profile Send private message
rlp



Joined: 27 Jun 2008
Posts: 2

PostPosted: Fri Jun 27, 2008 2:40 pm    Post subject: Reply with quote

YES it does!!!!

Thanks!!!
Back to top
View user's profile Send private message
john kanca



Joined: 14 May 2005
Posts: 6346

PostPosted: Fri Jun 27, 2008 2:48 pm    Post subject: Reply with quote

Our pleasure.

Thanks for using Surpass!

And please tell all your friends!

Wink
_________________
"You need me on that wall."


"You don't have a town named after you"
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Apex Information Exchange Forum Index -> About anchor® All times are GMT - 5 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group