Apex Information Exchange Forum Index Apex Information Exchange
Hosted by Dr. John Kanca III DMD
 
 FAQFAQ   SearchSearch   UsergroupsUsergroups   REGISTER 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Visit Apex Dental Materials     Upload Photos To Your Post


Search found 11 matches
Apex Information Exchange Forum Index
Author Message
  Topic: Durelon pulp cap with surpass?
k_h_d

Replies: 1
Views: 2556

PostForum: Apex Dental Materials, Inc.   Posted: Wed Feb 25, 2015 11:45 am   Subject: Durelon pulp cap with surpass?
I have read about using Durelon as a pulp cap and am concerned what it does to the bond with surpass? I use it with amalgams and have with a couple of composites. I have noticed that when using surp ...
  Topic: Surpass and contamination
k_h_d

Replies: 3
Views: 1832

PostForum: Apex Dental Materials, Inc.   Posted: Thu Nov 15, 2012 4:49 pm   Subject: Surpass and contamination
What do you do if you are in the middle of a restoration and you get saliva contamination. Today under RDI somehow some saliva seeped up on the occlusal surface. Rinsed and dried well, then reapplie ...
  Topic: Veener tryin and cementation
k_h_d

Replies: 5
Views: 2452

PostForum: Apex Dental Materials, Inc.   Posted: Mon Jul 16, 2012 1:02 pm   Subject: Veener tryin and cementation
I have read about the tack and wave technique which recommends a light cured cement. Titan has listed in its uses as a veneer cement. If I were to try that instead of dual cure anchor should I still ...
  Topic: Veener tryin and cementation
k_h_d

Replies: 5
Views: 2452

PostForum: Apex Dental Materials, Inc.   Posted: Mon Jul 16, 2012 8:05 am   Subject: Veener tryin and cementation
I am doing my first veneer case soon. I plan on using the shrinkwrap technique with surpass 2, 3, and protemp. What is a good material to use for tryin and then for cementation?

For cementation I ...
  Topic: Durelon pulp cap with surpass
k_h_d

Replies: 5
Views: 4433

PostForum: About Surpass   Posted: Wed May 30, 2012 6:17 pm   Subject: Durelon pulp cap with surpass
Today I had a patient in with recurrent decay under a very large occlusal composite on #18. Using rubber dam isolation the mesial pulp horn was exposed. Blood stopped almost immediately. I cleaned ...
  Topic: Notice
k_h_d

Replies: 9
Views: 8570

PostForum: About Titan   Posted: Sun Jan 29, 2012 3:19 pm   Subject: Notice
Does light activation of 20 seconds still apply with the newer more powerful curing lights? My Fusion curing light is very powerful and boasts that it can do all composites in 5 seconds. I do a coup ...
  Topic: Titan vs Gradia on radiographs
k_h_d

Replies: 1
Views: 1502

PostForum: Apex Dental Materials, Inc.   Posted: Fri Jan 20, 2012 8:53 am   Subject: Titan vs Gradia on radiographs
For the past 6 months I have been using Titan flowable as a base layer and Gradia Direct X. On recalls the Titan flowable is showing more radioopaque than the gradia direct X in the box. Its great s ...
  Topic: Surpass for bonding Parapost?
k_h_d

Replies: 8
Views: 5602

PostForum: About Surpass   Posted: Thu Jul 14, 2011 7:22 am   Subject: Surpass for bonding Parapost?
Found the surpass video of bonding a cerec... answered my questions...
  Topic: Surpass for bonding Parapost?
k_h_d

Replies: 8
Views: 5602

PostForum: About Surpass   Posted: Wed Jul 13, 2011 7:29 am   Subject: Surpass for bonding Parapost?
Quick question about bonding protocol for an inlay or onlay. The written instructions say to start with surpass 2. Why not start with surpass 1?

Do I have the following steps correct?

1. Inte ...
  Topic: Surpass for bonding Parapost?
k_h_d

Replies: 8
Views: 5602

PostForum: About Surpass   Posted: Tue Jul 12, 2011 5:56 pm   Subject: Surpass for bonding Parapost?
Good tip. What about for cementing inlays and onlays with Anchor and Surpass? Is air thinning enough or should excess be removed with a cotton ball?
  Topic: Surpass for bonding Parapost?
k_h_d

Replies: 8
Views: 5602

PostForum: About Surpass   Posted: Mon Jul 11, 2011 3:31 pm   Subject: Surpass for bonding Parapost?
I am looking for tips on bonding endo posts (paraposts) using surpass and anchor. Last time I tried it the post did not seat all the way and I had to reprep the post space and apply surpass again. I ...
 
Page 1 of 1
All times are GMT - 5 Hours
Jump to:  


Powered by phpBB © 2001, 2005 phpBB Group